Guide homeAll topicsDentsPaintVehicles & materialsSafetyFind a pro
DRAFT: general information, to be checked by a partner technician before publishing. It is not repair instructions for your vehicle; always follow the manufacturer's repair information.
Source-reviewed draft. Source review: done 24 October 2026 against public professional sources. Technician review: not done. Release decision: Jimmy.
Who is this for?
Know-only. Heat is the most misunderstood part of dent repair. Professionals use it with training, measurement and the manufacturer's limits. At home it is the easiest way to ruin paint or metal.
Heat changes how metal, plastic, glue and paint behave. A little warmth can help paint, glue and plastic flex. Too much can anneal (soften) metal, burn paint, melt adhesive and release fumes.
| Material | What heat does | What the sources say |
|---|---|---|
| Mild steel | Used by trained repairers to shrink stretched metal and ease straightening | Controlled use with temperature limits; some makers set limits by steel type |
| High-strength and ultra-high-strength steel | Heat can weaken it | Makers set limits by steel type: some allow tightly controlled heat on mild steel, none of the ones we read allow it on the strongest steels, and others restrict heat completely or say to replace at the factory seam. Always follow the manufacturer's matrix |
| Aluminium | Anneals (softens) and does not show a colour change to warn you | Makers set much lower limits than for steel, and a trade source says aluminium can soften permanently well below the temperatures used on steel. Use temperature indicators; limits vary, so follow the manufacturer |
| Plastic | Softens and can warp, discolour or release fumes | Welding and warming use set temperatures for the plastic type; unknown plastics are risky |
| Paint and clear coat | Blisters, cracks, discolours | Excess heat is a common cause of ruined paint |
| Adhesives (bonded panels) | Weakens | One manufacturer says bonded panel adhesive should not be heated beyond a set limit unless the panel is being removed; other sources say some adhesives start to break down at fairly low temperatures |
No temperatures are given here on purpose: the limits are set by each maker for structural repair, they differ by material and vehicle, and they are not safe limits for any home job.
Why the hair dryer and canned air or dry ice tricks usually fail
- Dents are held by stretched metal and stress, not by a dent being "stuck". A hair dryer does not heat metal enough or evenly enough to change that.
- Sudden cooling by compressed air or dry ice can crack paint, and does not return stretched metal to its shape.
- Our own look at DIY video tests found those tricks failed in most tests, with a few small successes that were not independently verified.
Infrared thermometers
- A non-contact thermometer is a sensible tool for checking a panel is warm, not hot.
- Readings on bare or shiny aluminium can be unreliable because the surface reflects heat. Professionals use heat-indicator crayons or strips and other methods.
- A thermometer does not tell you what the manufacturer allows.
What about warming a cold panel?
- Many DIY videos warm the paint on a cold day so glue tabs stick. We do not include heat in our DIY steps, because it is hard to judge by hand and the safe limit depends on the paint. Wait for a mild day and work in the shade instead. Glue kits that need a cold-day trick are a sign to book a professional.
Pros and cons
| Good | Not so good |
|---|---|
|
|
Do and don't
| Do | Don't |
|---|---|
|
|
- The panel is aluminium, composite or plastic
- The area is near a fuel tank, battery, airbag or sensor
- The paint feels hot, bubbles or changes colour
- You are tempted to use anything hotter than warm to the touch
Safety
- Burns and fires: keep flammables away and have a fire extinguisher nearby.
- Hot adhesives and glue guns cause burns.
- In an emergency call 000.
Sources and further reading
- I-CAR: Straightening and heat, General Motors
- I-CAR: Straightening and heat, Volkswagen
- AIA Canada: considerations for aluminium heat shrinking
- Tomorrow's Technician: fixing dents in aluminium
- Vehicle maker repair information: Body Structure Materials and Allowed Operations
Source links are for background only. Several are industry or supplier pages, so treat product claims with care. Technician sign-off: pending.
Rapid Repair is a free guide from the Hail Dent Repair team. Get a quote · Learn PDR properly · Phone 0408 020 468 · Disclaimer and terms