Rust: stages, causes and what to do

Guide homeAll topicsDentsPaintVehicles & materialsSafetyFind a pro

DRAFT: general information, to be checked by a partner technician before publishing. It is not repair instructions for your vehicle; always follow the manufacturer's repair information.

Source-reviewed draft. Source review: done 24 October 2026 against public professional sources. Technician review: not done. Release decision: Jimmy.

Check your warranty and insurance first. Repairs you do yourself, or have done by someone the manufacturer has not approved, may void or reduce your paint, corrosion or other warranties, and may affect insurance claims, finance conditions and resale. Read your warranty booklet or ask the manufacturer or your insurer before you start. This is general information, not legal advice. Read more

Who is this for?

Everyone. Prevention and early checking are the DIY part. Treating rust is not on our DIY list: photograph it and ask us first. Anything deeper than a tiny spot is a repairer job, and rust on a structural panel is a safety issue.

Rust is steel reacting with oxygen and moisture. It usually starts where paint is chipped or where water collects, and it spreads under the paint.

StageWhat you seeWhat usually happens
Surface rustOrange speckles or a light film; paint bubbles startingA repairer sands back, treats, primes and repaints. Not on our DIY list: if it is tiny and not structural, ask us first (and do the warranty check above)
Scale rustRough, flaky patches; metal beneath is being eatenGrind or blast back to clean metal, seal and refinish; usually a repairer job
Perforation (penetrating rust)Holes or soft, crumbling metalCut out and weld in new metal or replace the panel; professional only

Costs: [CHECK: rust repair cost range]. The cost listings we found were templated across models, so none are quoted here.

Rust stages and what usually happensThree cross-sections of a panel. Stage one is surface rust under bubbling paint. Stage two is flaky scale rust eating the metal. Stage three is a hole through the panel. Treating rust is not a home job: for tiny non-structural surface rust, photograph it and ask us first; the other stages need a repairer.Three stages of rust (cross-section, not to scale)1 Surface rustSpecks, bubbles2 Scale rustFlaky, eats metal3 PerforationHoles, crumblingTiny and notstructural only:ask us firstRepairer job:grind back,seal, refinishProfessionalonly: cut outand weld inRust on sills, rails, pillars or floor is structural: see a pro.
Illustrative and simplified, not to scale. Based on the stages in the table above. Rust on structural or safety panels always needs a qualified repairer, and any home treatment may affect warranties.

Causes

  • Chips, scratches and failed paint that expose steel.
  • Water trapped in seams, door bottoms, sills and under trims.
  • Salt (coastal air, winter roads), mud and neglected cleaning.
  • Previous poor repairs, and zinc coatings destroyed by welding or grinding.
  • Aluminium does not rust but can corrode (white powder) especially next to steel.

Prevention (and maintenance)

  • Wash regularly, including wheel arches and underbody after beach or salt.
  • Seal paint chips quickly (see chips and touch-up).
  • Keep drain holes clear and trims dry.
  • Garage or cover the vehicle, and fix leaking seals.
  • Inspect paint at 5, 7 and 10 years, and after hail or scrapes.

Structural and safety panels

  • Rust on sills, chassis rails, pillars, suspension mounts, seat belt anchors or the floor can weaken crash protection. These need a qualified repairer and may fail a roadworthy inspection.
  • Do not patch with filler, fibreglass or sealant over holes.

Pros and cons

GoodNot so good
  • Early treatment stops rust spreading
  • Small surface rust can be repaired cheaply
  • Prevention is cheap compared with panel replacement
  • Rust often looks small outside and is bigger underneath
  • DIY covers often hide the problem and let it grow
  • Welding and grinding near zinc coatings produce fumes and damage protection

Do and don't

DoDon't
  • Wash and dry the area and check how far it has spread
  • Photograph it and send it for a quote if unsure
  • Photograph tiny surface spots promptly and send them to us before treating anything
  • Paint over rust without removing it
  • Fill holes with body filler
  • Ignore bubbles under paint
Stop rules: stop and get a quote if...
  • The rust has holes, soft metal or flaking
  • It is on a sill, rail, pillar, floor or near the suspension
  • The panel bubbles over a large area
  • It sits next to a dent (rust can be hidden under filler or paint)

When to see a panel shop

  • Any scale rust or perforation, any structural area, and rust together with dents or cracked paint.
Not sure? Don't touch it yet. Most damage is cheaper to fix properly than to fix twice. Get a quote or call 0408 020 468.

Sources and further reading

Source links are for background only. Several are industry or supplier pages, so treat product claims with care. Technician sign-off: pending.

Rapid Repair is a free guide from the Hail Dent Repair team. Get a quote · Learn PDR properly · Phone 0408 020 468 · Disclaimer and terms

Ever wondered how we fix dents without paint?

Learn the craft: a 51-video online course taught by a 20-year PDR technician, the PDR eBook on running a PDR business, or 1-on-1 hands-on training.

Start your 7 day free trial